Dynamic Engineering PMC2PCI Specifikace Strana 26
- Strana / 128
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
HARDWARE INSTALLATION
2-4 PP 41x/03x
2.4 Front Panel Indicators and Controls
When installing or removing the board for the first time, or when checking its operation, it can be
very useful to note the behavior of the LEDs on the front panel. Figure 2-2 shows the location of
the LEDs, and their purpose is outlined below.
Figure 2-2 Front Panel Indicators and Controls
2.4.1 Run LED (R) Green
The run LED indicates that activity is occurring on the LPC bus or the 32-bit PCI bus. This allows
the user to quickly assess how active the busses are.
2.4.2 POST LED (P) Yellow
The POST LED is used to indicate that a power on self test has failed. This LED will also flash
when outputting sound on the speaker.
2.4.3 Ethernet Speed LED (SPD) Yellow
This LED indicates the operating speed of the front panel Ethernet interface, as follows:
• Off = 10Mbits/s
• Steady On = 100Mbits/s
• Flashing = 1000Mbits/s
2.4.4 Ethernet Link/Activity LED (LK/ACT) Green
This LED lights when connection has been made on the front panel Ethernet interface. It will flash
to indicate link activity, and during periods of high Ethernet activity the LED may switch off for
several seconds.
2.4.5 User LED (U) Red
This LED is available for use by user software. It is manipulated via an I/O register (see Section
9.2 for details). Alternatively, the User LED may be configured to light when the CPU reaches its
maximum specified operating temperature (see Section 11.2.3). In either mode, the User LED will
flash rapidly if the CPU Thermal Trip activates (see Section 11.2.6).
2.4.6 Hot-Swap LED (HS) Blue
This LED is used when the board is hot-swapped, and lights to indicate when the board can be
safely removed from the chassis.
2.4.7 EIDE Activity LED (I) Yellow
This LED lights when there is activity on the on-board EIDE interfaces or the SATA interfaces.
- CONVENTIONS 2
- NOTATIONAL CONVENTIONS 2
- GLOSSARY OF TERMS 3
- REVISION HISTORY 4
- TABLE OF CONTENTS 5
- TABLE OF FIGURES 10
- TABLE OF TABLES 11
- 1 INTRODUCTION 13
- INTRODUCTION 14
- 2 HARDWARE INSTALLATION 23
- HARDWARE INSTALLATION 24
- 3 SOFTWARE INSTALLATION 45
- SOFTWARE INSTALLATION 46
- SOFTWARE INSTALLATION 47
- 4 MASS STORAGE INTERFACES 49
- MASS STORAGE INTERFACES 50
- 5 ETHERNET INTERFACES 51
- ETHERNET INTERFACES 52
- 6 OTHER INTERFACES 53
- OTHER INTERFACES 54
- INTERFACE 57
- 7.2 IPMI Compatibility 58
- 7.3 IPMI Overview 59
- 7.3.4 Sensors 60
- 7.3.5 Sensor Data Records 60
- 7.3.7 Watchdog 60
- 7.4 Supported Commands 61
- 7-6 PP 41x/03x 62
- 7.4.2 Watchdog Commands 63
- 7.4.3 SEL and SDR Commands 63
- 7.4.4 Sensor Commands 64
- 7.5 FRU Inventory Data 67
- 7.5.2 Board Area 68
- 7.6 Programming Examples 69
- 7-14 PP 41x/03x 70
- PP 41x/03x 7-15 71
- 7-16 PP 41x/03x 72
- PP 41x/03x 7-17 73
- 7.6.3 Reading Sensors 75
- 7-20 PP 41x/03x 76
- 7.7 In System Programming 77
- 7-22 PP 41x/03x 78
- 8 FLASH EPROM AND DRAM 79
- FLASH EPROM AND DRAM 80
- 7 6 5 4 3 2 1 0 83
- CONSOLE USER MODE 83
- 9.5 CPCI Status Register 87
- 7 6 5 4 3 2 1 0 89
- D7 D6 D5 D4 D3 D2 D1 D0 89
- 9-10 PP 41x/03x 90
- 9.10 IPMI SMIC Interface 92
- 9.11 P.O.S.T. LED / Speaker 93
- 9.12 PORT 80 94
- 10 PC BIOS 95
- PC BIOS 100
- 11 SYSTEM MANAGEMENT 107
- SYSTEM MANAGEMENT 108
- SYSTEM MANAGEMENT 109
- A SPECIFICATIONS 111
- SPECIFICATIONS 112
- SPECIFICATIONS 113
AEG S75398KG podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Zamrażarki AEG S75398KG.
Dostarczamy 1 pdf podręczników AEG S75398KG do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce